八大胜

Product features

• ▪ 7-inch touch screen operation;
  
• ▪ Support multi language, convenient for different users;
  
• ▪ Built in environment automatic detection program, automatically detect the test environment and remind users;
  
• ▪ Programmable operation, realizing the setting function with one key;
  
• ▪ Built in international standard grade parameters, easy and fast operation;
  
• ▪ The highest pulse frequency is up to 1200khz;
  
• ▪ Rs232/usb interface, which can be controlled by PC and print test report.

Product parameters

• Product model
  

  Meet the standard
  

  Operation mode
  

  output voltage
  

  Pulse frequency
  

  Pulse polarity
  

  Running time
  

  internal resistance
  

  midpsulse front
  

  pulse width
  

  Output mode
  

  Coupling output
  

  Number in pulse
  

  Phase angle
  

  Pulse train period
  

  Coupling / decoupling network
  

  Working power supply
  

  ambient temperature

• EFT S6
  

  IEC61000-4-4、GB/T 17626.4
  

  7.0 inch full-color touch screen
  

  0.2~± 6KV
  

  1khz~1200khz ± 10%, continuously adjustable
  

  Positive, negative, positive before negative, negative before positive
  

  1 ~9999s, continuously adjustable
  

  50 Q±10%
  

  5ns ± 30%
  

  50ns ± 30% (50Q load) /35 ns ~150 ns (1kq load)
  

  IEC, customization, programming
  

  BNC, coupling decoupling network
  

  1 ~ 255, continuously adjustable
  

  0~360 ° synchronous or asynchronous
  

  0.15~99.9s, continuously adjustable
  

  Built in, single-phase three wire, 16A
  

  AC220V± 10% 50/60Hz
  

  15C~35°C

Product recommendation

Single Phase 10A Voltage Dips Generator

Model：VDT S10

Voltage dips/sags, short interruptions are caused by failures of the power grid and power facilities or sudden large changes in loads. In some cases, there will be two or more consecutive dips or interruptions. Voltage changes are caused by continuous changes in the loads connected to the grid. If the EUT cannot respond in time to changes in the power supply voltage, it may cause malfunctions. Voltage dips generators are used to evalsuate the performance of electrical and electronic equipment when subjected to voltage dips/sags, short interruptions, and voltage changes. Products fully meet the requirements of standards IEC/EN 61000-4-11 and GB/T17626.11.

Learn more

Impulse current generator sur 6ka

Model：SUR 6KA

The lightning surge generator sur 6ka is used to inspect the anti surge protection devices such as zinc oxide arrester valve piece, varistor, SPD, TVs tube, gas discharge tube, etc. for surge impact test. The product produces 8/20us surge pulse waveform, and the technical indicators of the waveform comply with the provisions of national standards and IEC standards.

Learn more

Single phase 6kV burst generator EFT S6

Model：EFT S6

In the circuit, such as from the switching transient process (cutting off inductive loads, bouncing relay contacts, etc.), it will usually interfere with other electrical and electronic equipment in the same circuit. This kind of interference is characterized by high amplitude, short rise time, high repetition rate and low energy. Clusters of narrow pulses can charge the junction capacitance of semiconductor devices, which may cause circuit or equipment errors when accumulated to a certain extent. The burst generator determines a common reproducible evalsuation basis for evalsuating the performance of power supply ports, signal, control and grounding ports of electrical and electronic equipment when disturbed by electrical fast transient bursts. The products meet the requirements of new standards such as iec61000-4-4, en60100-4-4 and gb/t17626.4.

Learn more